Adsorption of gas molecules on monolayer MoS2 and effect of applied electric field

1Sensing gas molecules, especially toxic gas, is critical in environmental pollution monitoring and agricultural and medical applications. For this reason, sensitive solid-state sensors with low noise and low power consumption are highly demanded. While sensors made from semiconducting metal oxide nanowires, carbon nanotubes, etc. have been widely studied for gas detection for some time, graphene as a novel sensing material has further stimulated strong interests in the research community since Schedin et al. demonstrated that a micrometer-sized graphene transistor can be used to detect the ultimate concentration of molecules at room temperature, presenting a pronounced sensitivity many orders of magnitude higher than that of earlier sensors. The graphene-based sensor is actualized by monitoring the change in resistivity due to the adsorption or desorption of molecules, which act as charge acceptors or donors. It is shown that sensitivity of this sensor can be further improved through introduction of the dopant or defect in graphene. Despite these achievements, researchers continue to seek for novel sensitive sensors similar to or even more fascinating than graphene gas sensors.

2Recently, two-dimensional monolayer MoS2, a kind of transition metal dichalcogenide, has attracted increasing attention because of its versatile and tunable properties for application in transistor, flexible optoelectronic device, photodetector, and so on. Unlike graphene which lacks a band gap and needs to be engineered to open the gap for practical application, pristine monolayer MoS2 has a direct band gap of 1.9 eV and can be readily used to fabricate an interband tunnel field-effect transistor (FET). In this context, Radisavljevic and co-workers first reported a top-gated FET on the basis of monolayer MoS2, which possesses a room-temperature current on/off ratio exceeding 108 and mobility of 200 cm2 V-1 s-1. At the same time, the success of graphene-FET sensors also greatly inspires the intensive exploration of MoS2 as a sensing material. Since monolayer MoS2 holds a high surface-to-volume ratio comparable to graphene, a MoS2-based gas sensor is expected to have excellent sensing performance as well. More recently, FET sensors made from mechanically cleaved monolayer and multilayer MoS2 have been demonstrated, which exhibit high sensitivity for NO gas with a detection limit down to 0.8 ppm. The superior sensitivity for NO2 has been observed in a flexible FET sensor array on a polyethylene terephthalate (PET) substrate based on a MoS2 channel and reduced graphene oxide (rGO) electrodes. Compared to the rGO-FET sensor, this novel sensor array displays much higher sensitivity, which can even be enhanced by up to three times via functionalization of MoS2 with Pt nanoparticles.

3Although the MoS2-FET sensor for nitride oxide has been experimentally realized, the underlying mechanisms regarding how NOx molecules interact with the MoS2 surface and affect the electronic properties are not clear. Moreover, the response of MoS2 upon exposure to other gas molecules like H2, O2, H2O, NH3, CO, etc. remains to be examined either. In order to fully exploit the possibilities of a MoS2-based gas sensor, a systematic study on the adsorption of gas molecules on a MoS2 surface is thus desired from a theoretical point of view. In this work, using first-principles calculations, we first determine the most stable configuration for gas molecules adsorbed on monolayer MoS2, as well as the corresponding charge transfer between them. Modification of the electronic properties of host monolayer MoS2 due to the molecule adsorption is then examined. Furthermore, the effect of an external electric field on the charge transfer is also discussed. To the best of our knowledge, no prior theoretical work has been conducted on these issues.

4First-principles calculations are performed using the Vienna ab initio simulation package (VASP) on the basis of density functional theory (DFT). The exchange-correlation interaction is treated by local spin density approximation (LSDA). Spin-polarized calculations are also carried out with generalized gradient approximation (GGA) in some specific cases. A cutoff energy of 400 eV for the plane-wave basis set and a Monkhorst-Pack mesh of 5 × 5 × 1 for the Brillouin zone integration are employed. In order to eliminate the interaction between two adjacent monolayer MoS2, a vacuum layer larger than 15 Å is adopted in the calculations. All the structures are fully relaxed by using the conjugate gradient method until the maximum Hellmann-Feynman forces acting on each atom is less than 0.02 eV/Å. By means of Bader analysis, charge transfer between the monolayer substrate and the adsorbate is obtained. The electric field in VASP is actualized by adding an artificial dipole sheet at the center of the simulation cell.

5We consider the absorption of H2, O2, H2O, NH3, NO, NO2, and CO on two-dimensional monolayer MoS2. A 4 × 4 supercell of monolayer MoS2, with a single gas molecule adsorbed to it, is chosen as the computational model. The optimized lattice constant of monolayer MoS2 is 3.12 Å, and consequently, the distance between two neighboring gas molecules is larger than 12 Å. The monolayer MoS2 consists of a monatomic Mo-layer between two monatomic S-layers like a sandwich structure, in which Mo and S atoms are alternately located at the corners of a hexagon. In order to determine the favorable adsorption configuration, four adsorption sites are considered, namely, H site (on top of a hexagon), TM (on top of a Mo atom), TS (on top of a S atom), and B site (on top of a Mo-S bond). The gas molecule is initially placed with its center of mass exactly located at these sites. For each site, configurations with different molecular orientations are then examined. Take NO as an example, three initial molecular orientations are involved, one with NO axis parallel to the monolayer and two with NO axis perpendicular to it, with O atom above N atom and O atom below N atom [see Additional file 1 for more detailed adsorption configurations]. The adsorption energy is calculated as, where is the total energy of MoS2 with an absorbed molecule and and Emolecule are the total energies of pristine MoS2 and isolated molecule, respectively. A negative value of Ea indicates that the adsorption is exothermic.

6Table 1 summarizes the calculated values of equilibrium height, adsorption energy, and charge transfer for the adsorption of gas molecules on monolayer MoS2. The values for each adsorbate correspond to its favorable adsorption configurations obtained at different sites. The equilibrium height is defined as the vertical distance between the center of mass of the molecule and the top S-layer of the MoS2 sheet. Note that the adsorption energies are often overestimated at the LDA level, but this is not very essential here because we are primarily interested in the relative values of adsorption energies for different configurations and finding the most favorable one among them. From Table 1, we see that for both H2 and O2, the TM site is found to be their most favorable site with the adsorption energies of -82 and -116 meV, respectively. The corresponding structures are shown in Figure 1a,b. Nevertheless, it seems that the two molecules adopt distinct orientations. While H2 has an axis perpendicular to the monolayer, that of O2 is nearly parallel to the monolayer with its center of mass on top of the TM. H2O, NH3, and NO2 are preferably adsorbed at the H site, resulting in the adsorption energies of -234, -250, and -276 meV, respectively. Structures for the three systems are shown in Figure 1c,d,f. Contrary to the configuration for H2O where H-O bonds adopt tilted orientation with H atoms pointing at the monolayer, all the H atoms of NH3 point away from the monolayer. NO2 is bonded with O atoms close to MoS2. In our calculations, H2, O2, H2O, and NH3 fail to have stable configuration at the B site; this is because they tend to migrate to other sites during structural relaxations. In contrast, the configuration with the center of mass located at the B site is found to be the most favorable one for NO, as shown in Figure 1e. The corresponding adsorption energy is determined to be -211 meV. The CO molecule somewhat favors both H and B sites, giving an identical absorption energy of -128 meV (see Figure 1g). For simplicity, the configuration at the H site is chosen as the representative for CO. All of the following results for these adsorbates are obtained based on their most favorable configurations if not specified.

7Additionally, calculations of the gas adsorption are also performed using GGA functional. Different from LDA functional which overestimates the adsorption energy, GGA functional usually has a tendency to underestimate it. Upon the application of the two kinds of functionals, the upper and lower bounds for adsorption energy and other structural properties can be obtained. The calculated values of equilibrium height and adsorption energy for gas molecules on MoS2 are listed in Table 2. Herein, two GGA functionals, PW91 and PBE, are used for the purpose of comparison. Both PW91 and PBE give a smaller adsorption energy compared to the LDA, whereas they show the molecules binding at an equilibrium height larger than that for LDA. For most molecules (with the exception of NO), it seems that PW91 gives more stable results than PBE, with their adsorption energy difference approximately between -7 and -28 meV.

8Next, Bader analysis is performed to predict the charge transfer value. It is found that most molecules studied except NH3 are charge acceptors with 0.004 ∼ 0.1e obtained from monolayer MoS2, whereas NH3 behaves as a charge donor, providing 0.069e to the monolayer. The charge transfer values for O2 and H2O are in good agreement with recently reported values (approximately 0.04e for O2 and 0.01e for H2O) by Tongay et al.. Note that our results are somewhat similar to the previous reports on the adsorption of gas molecules on graphene and carbon nanotube, where the gas molecules also behave as either charge acceptors or donors. We need to point out that although different methods besides Bader analysis may give rise to different values in determining the electronic charge transfer, the direction and order of magnitude should be the same. The mechanism of the MoS2-FET gas sensor for NO can then be understood. Before NO adsorption, the mechanically cleaved MoS2 channel is an n-type semiconductor in the experiment, implying that some electrons have already existed in the conduction band. After NO adsorption, electron charge is transferred to the NO molecule, inducing a p-doping effect on the MoS2 channel. As a result, the channel resistance increases and current decreases. The similar behavior, which has been previously reported for MoS2-FET devices in an O2 environment, is probably due to the adsorption of O2 on the MoS2 surface, which traps electrons and sequentially reduces the current of the MoS2-FET.

9To further gain insight into the molecule-monolayer interaction, we calculate the adsorption energy curves for all the studied gas molecules, wherein the height between the center of mass of the molecule and the top S-layer of the MoS2 sheet is varied between 1.5 and 5.0 Å. The corresponding results are given in Figure 2. It is shown that the curve for NO2 gives the largest adsorption energy at the minimum, which is three times higher than that of the H2 curve. At equilibrium, NH3 has a minimum height of 2.46 Å with respect to monolayer MoS2, whereas CO has a maximum molecule-monolayer height of 2.95 Å. All the curves nearly reach the asymptotic value at 5.0 Å. Due to the small adsorption energy and large separation height, the interaction between the gas molecules and the MoS2 surface can thus be characterized as physisorption.

10Figure 3 presents the charge density difference images for these molecule-monolayer systems, calculated by the formula, where,, and ρmolecule are the charge density of the molecule-adsorbed MoS2, pristine MoS2, and isolated molecule, respectively. The red region shows the charge accumulation, while the green region represents the charge depletion. It is shown that the MoS2 sheet is considerably polarized upon the adsorption of gas molecules, and electrostatic interaction plays a role in the attractive interaction. The polarization in the H2O, NH3, NO, and NO2 cases are stronger than that in the O2 and CO cases, giving rise to a larger interaction energy. It explains why the former gives larger adsorption energies (-234, -250, -211, and -276 meV for H2O, NH3, NO, and NO2, respectively) than the latter (-116 and -128 meV for O2 and CO, respectively) mentioned above.

11We examine the electronic properties of monolayer MoS2 adsorbed with gas molecules. The band structure before adsorption is presented in Figure 4a. It is found that the pristine monolayer MoS2 is a semiconductor with a direct band gap of 1.86 eV at K point, which is in good agreement with reported works. The band structures for both valence bands and conduction bands of monolayer MoS2 are not significantly altered when H2O, NH3, and CO are adsorbed, and the gap values remain around 1.86 eV (not shown here). The situation is similar in the cases of O2, NO, and NO2 except the flat impurity states in the gap of the host monolayer induced by these adsorbates. While O2 introduces two close-lying down-spin states 0.519 and 0.526 eV above the Fermi level (EF) in the band gap, NO2 introduces an unoccupied down-spin state 0.31 eV above EF, as given in Figure 4c. Three impurity states emerge inside the band gap upon the adsorption of NO, namely, one occupied up-spin state 0.12 eV below EF, one unoccupied up-spin state 0.11 eV above EF, and one unoccupied down-spin state close to the conduction band edge with an energy separation of 0.064 eV between them (see Figure 4b). The adsorption of O2, NO, and NO2 on the MoS2 surface, on the other hand, creates magnetic moments of 2.0, 1.0, and 1.0 μB per supercell, respectively.

12As the charge transfer between the adsorbed molecule and monolayer MoS2 plays a crucial role in determining the performance of the MoS2 sensor, it may be sensitive to the applied electric field, similar to the case of graphene. For brevity, NO and NO2 adsorbed monolayers are chosen as the representative systems. Figure 5a gives the schematic illustration of the electric field applied in our study, which is perpendicular to the plane of monolayer MoS2 with its positive direction aligned upward. The variation of charge transfer with respect to the electric field is shown in Figure 5b. It is found that the charge transfer from the monolayer to the adsorbed molecule increases with the increment of field strength along a positive direction, whereas it tends to decrease once reverse electric field is applied. This negative electric field will drive the electrons from the molecule to the monolayer when its field strength is beyond a critical value. While NO and NO2 attain 0.022e and 0.1e in the absence of electric field (E = 0 V/Å), respectively, they turn out to accept 0.225e and 0.39e from monolayer MoS2 at E = 1 V/Å and conversely donate 0.21e and 0.028e at E = -1 V/Å. The dependence of charge transfer on field direction is probably attributed to the dipole moment of the molecule-monolayer system. Band structure calculations for the two systems, on the other hand, show that the impurity states in the band gap shift towards the valence or conduction bands of monolayer MoS2, depending on the direction of the applied perpendicular electric field.

13In this work, we present a first-principles study on the structural and electronic properties of monolayer MoS2 upon adsorption of gas molecules. Various adsorption sites and molecule orientations are involved to determine the most stable configurations. We find that all molecules are physisorbed on monolayer MoS2 with small charge transfer, acting as either charge acceptors or donors. Band structure calculations indicate that the valence and conduction bands of monolayer MoS2 is not significantly altered upon the molecule adsorption, though certain molecules such as O2, NO, and NO2 introduce adsorbate states in the band gap of the host monolayer. In addition, we demonstrate that the application of a perpendicular electric field can consistently modify the charge transfer between the adsorbed molecule and the MoS2 substrate. Our theoretical findings show that MoS2 holds great promise for fabricating gas sensors.

14The authors declare that they have no competing interests.

15QY performed the first-principles calculations and drafted the manuscript. ZS and SC participated in the calculation part. JL conceived of the study and helped in writing of the manuscript. All authors read and approved the final manuscript.